原因1。裝修施工處理不當开摄,墻基不夠干燥售拼,或原水泥層不干凈直接刷膩?zhàn)樱?/div>
Reason 1. Improper treatment of decoration construction, insufficient dryness of wall foundation, or unclean original cement layer, directly apply putty;
處理方法:涂乳膠漆前且昭,做好裝修前期工作,打開室內各房間的門窗贱鼻,使室內墻壁和地面盡快干燥宴卖。如果條件允許,可以去除空氣中的水分邻悬,避免乳膠漆在潮濕環境中發霉症昏。
Treatment method: before applying emulsion paint, do the preliminary work of decoration, open the doors and windows of indoor rooms, and dry the indoor walls and ground as soon as possible. If conditions permit, the moisture in the air can be removed to prevent the latex paint from mildew in the humid environment.
原因2:材料本身質量差,如膩?zhàn)淤|(zhì)量問題父丰;
Reason 2: the quality of the material itself is poor, such as the quality of putty;
處理方法:建議購買材料時不要貪圖便宜肝谭,要選擇知名的材料。另外蛾扇,刮膩?zhàn)雍腿槟z漆時要注意工藝安排攘烛,刮膩?zhàn)雍笸9滋欤WC干燥镀首,一次涂乳膠漆后延長干燥時間坟漱。
Treatment method: it is recommended not to be greedy for cheap when purchasing materials, but to choose well-known materials. In addition, pay attention to the process arrangement when scraping putty and emulsion paint. Stop work for several days after scraping putty to ensure drying. Extend the drying time after applying emulsion paint at one time.
原因3:墻面是否長期受潮,墻面長期受潮也會引起乳膠漆墻面鼓包現象蘑斧;
Reason 3: whether the wall is damp for a long time, and the long-term damp of the wall will also cause the bulge of latex paint wall;
處理方法:檢查是否有水龍頭或其他可能導致滲水的設備靖秩。如果是這樣,首先修理水龍頭和水管堡喳,以確保這些設備不再滲水件父。拆除鼓包處的墻壁,鏟掉起泡部分的墻壁祸播,重新處理夹它。
Treatment method: check whether there are faucets or other equipment that may cause water seepage. If so, first repair the faucet and water pipe to ensure that the equipment is no longer leaking. Remove the wall at the bulge, shovel off the wall at the bubbling part and reprocess it.
膩?zhàn)臃燮鹋萁鉀Q方法:
Solution to foaming of putty powder:
1.如有大面積起泡,建議直接用鏟子壓小泡口遭唠,用膩?zhàn)釉俅喂卧谄鹋荼砻妗?/div>
1. In case of large-area foaming, it is recommended to directly press the bubble mouth with a shovel and scrape it on the foaming surface again with putty.
2.先打磨舊墻恢儡,增加墻面粗糙度,再用家園強化界面處理劑均勻涂抹在墻面基層1~2次颊姻。
2. First polish the old wall to increase the roughness of the wall, and then evenly apply the home strengthening interface treatment agent to the base course of the wall for 1 ~ 2 times.
3.大理石组莲、馬賽克、瓷磚等外墻表面選用外墻翻新膩?zhàn)哟虻住?/div>
3. Marble, mosaic, ceramic tile and other exterior wall surfaces shall be primed with exterior wall renovation putty.
4.攪拌膩?zhàn)臃蹠r(shí)矫恳,建議使用手電鉆攪拌機咒饼,確保膩?zhàn)臃蹟嚢杈鶆颉?/div>
4. When mixing the putty powder, it is recommended to use the electric hand drill mixer to ensure that the putty powder is mixed evenly.
5.使用膩?zhàn)臃蹠r(shí),一定要注意保質期刮赵,在保質期內使用渔硫。
5. When using putty powder, be sure to pay attention to the shelf life and use it within the shelf life.
???