Jinan putty powder you may have heard, but some people may still ask: what is putty powder. As a kind of grass-roots building materials, its use is very wide, so what impact does it have on grass-roots materials? Today, Fuhua building materials analyzes this problem for you.

所謂膩子粉膩子又稱為填泥，屬于一種厚漿狀涂料鼻弧。涂施于底漆上或直接涂施于物體上，用以清除被涂物表面上高低不平的缺陷惯裕。

The so-called putty powder putty, also known as filling mud, belongs to a thick paste coating. It can be applied on the primer or directly on the object to remove the uneven defects on the surface of the object to be coated.

它由少量的漆基、大量的填料和適量的著色顏料制成绣硝。使用的顏料主要是鐵紅蜻势、炭黑撑刺、鉻黃等。填料主要是重質碳酸鈣握玛、滑石粉等够傍。它可以用局部凹陷填充工作表面或刮掉整個表面。通常在底漆層完全干燥后挠铲，將其涂在底漆層的表面冕屯。

It is made of a small amount of lacquer base, a large amount of filler and an appropriate amount of pigment. The main pigments used are iron red, carbon black, chrome yellow, etc. The main fillers are heavy calcium carbonate, talc, etc. It can fill the working surface with local depressions or scrape off the whole surface. It is usually applied to the surface of the primer after it has completely dried.

現象：施工完成并仔細干燥后，用手觸摸會掉粉网孕。

Phenomenon: after the construction is completed and carefully dried, the powder will drop when touching with hands.

濟南膩子粉產生這種現象的原因：

The reasons for this phenomenon are as follows

1蒿庙、內墻膩子粉拋光時間不好，表面已經干燥慢筝，然后拋光處理將去除粉末;

1. The internal wall putty powder polishing time is not good, the surface has been dry, and then polishing will remove the powder;

2砖蕾、外墻膩子粉飾面時涂層相對較薄。夏季高溫條件下贮秤，水分揮發快廷共，表層水分不足無法固化，因此容易脫粉巴俺。

2. The coating of exterior wall putty powder is relatively thin. Under the condition of high temperature in summer, the moisture volatilizes quickly, and the surface moisture is insufficient to solidify, so it is easy to remove the powder.

3诸鲸、產品超過保質期，粘接強度大大降低诈猎。

3. The adhesive strength of the product is greatly reduced when it exceeds the shelf life.

4使驰、產品儲存不當會大大降低吸濕后的附著力。

4. Improper storage of products will greatly reduce the adhesion after moisture absorption.

5映僚、基層的高吸水率導致膩子快速干燥寞竭，沒有足夠的水來固化。

5. The high water absorption of the base causes the putty to dry quickly and there is not enough water to cure.

解決方法：

resolvent:

濟南膩子粉

Jinan putty powder

1酣难、拋光內壁膩子表面時谍夭，應掌握合適的拋光時間。拋光時間是在水印消失后立即拋光膩子表面憨募。實踐證明紧索，1~2m2的單板應平整或打磨。

1. When polishing the surface of inner wall putty, the appropriate polishing time should be mastered. The polishing time is to polish the putty surface immediately after the watermark disappears. Practice has proved that 1 ~ 2M2 veneer should be flat or polished.

2菜谣、外墻膩子表面干燥后珠漂，應適當打磨，并充分澆水濕潤尾膊。一般維護應分為兩次或兩次以上媳危。如有必要，請用透明封閉底漆兌水(1：5)作為二道淋水液，效果會更好待笑。

2. After the surface of external wall putty is dry, it should be properly polished and fully watered. General maintenance should be divided into two or more times. If necessary, use the transparent sealing primer mixed with water (1:5) as the second spray, the effect will be better.

3鸣皂、產品需要在保修期內使用。超過保修期時暮蹂，需要進行試刮维瑰，檢查合格后方可施工。

3. The product needs to be used within the warranty period. When the warranty period is over, trial scraping shall be carried out, and construction can only be carried out after the inspection is qualified.

4鼻发、產品需要注意防水處理茶窍，應存放在陰涼干燥的地方，并保證封裝完好辑奔。

4. Products need to pay attention to waterproof treatment, should be stored in a cool and dry place, and ensure good packaging.

5扫帝、在夏季或高溫大風氣候下，涂抹膩子前要先用清水濕潤墻面哎闻，待墻面無明水后再涂抹膩子

5. In summer or high temperature and gale climate, before applying putty, wet the wall with clean water, and then apply putty when there is no clear water on the wall

以上就是濟南膩子粉對基層材料影響的簡介了敏卦，希望能夠?qū)δ兴鶐椭Ｈ绻蠹覍τ谶€想了解更多的關于建筑材料的知識枚林，或者其相關產品知識米鹏，歡迎前來我們的網站咨詢，我們將竭誠為您服務郭菜。

The above is the brief introduction of the influence of Jinan putty powder on the base material, hoping to help you. If you want to know more about building materials, or its related product knowledge, welcome to our website, we will serve you wholeheartedly.