膩?zhàn)臃塾袝r(shí)在施工或一段時間后會出現氣泡踩林。原因:
Putty powder sometimes appears bubbles after construction or a period of time. reason:
1.原因可能是底座過于粗糙面徽，打擊速度過快;
1. The reason may be that the base is too rough and the strike speed is too fast;
2.膩?zhàn)訉犹褚淮问┕で富睿笥?.0mm;
2. The putty layer is too thick for one construction, more than 2.0mm;
3.基層含水率過高，密度過大或過小乙遵。由于膩?zhàn)涌紫敦S富抖臭，含水率高，不透氣式蠢，空氣在孔隙腔內封閉廉贤，不易消除。施工一段時間后遥妒，僅在表面出現氣泡爆裂卧蒂，主要原因是攪拌不均勻，料漿含小于溶解的粉末顆粒珍询，施工后圆乡，大量吸水，膨脹爆裂策橘。
3. The moisture content of the base course is too high, the density is too large or too small. Due to the rich pores, high moisture content, airtight, air in the pore cavity closed, not easy to eliminate. After construction for a period of time, only bubbles burst on the surface, the main reason is that the mixing is uneven, the slurry contains less than the dissolved powder particles, after construction, a large number of water absorption, expansion burst.
如膩?zhàn)臃鄢霈F(xiàn)大面積發泡膩?zhàn)用嬲ǘ桑苗P刀直接壓碎小泡口，再用適當?shù)哪佔庸稳グl(fā)泡表層;膩?zhàn)臃垡话銛嚢杈鶆蚶鲆眩o置約10分鐘后蚌堵，再用電動攪拌機在墻上攪拌均勻;施工第二層或一層表面層起泡現象，應在水印消除前用刮板壓破氣泡處理沛婴，以保證膩?zhàn)颖砻娌怀霈F(xiàn)氣泡;非凡粗糙的墻面吼畏，一般基材盡量選用粗膩?zhàn)臃?在墻面過干或風、光強的環境下嘁灯，先盡可能用清水濕潤墻面泻蚊。墻沒有清水后躲舌，進行膩?zhàn)訉拥墓纬?/div>
If the putty powder has a large area of foaming putty surface, use a blade to directly crush the small bubble mouth, and then use a suitable putty to scrape off the foaming surface; generally, the putty powder is evenly stirred, and after standing for about 10 minutes, use an electric mixer to evenly stir on the wall; In order to avoid bubbles on the surface of the second or last layer of the construction, a scraper shall be used to break the bubbles before the watermark is eliminated to ensure that there is no bubbles on the putty surface; for the particularly rough wall, the coarse putty powder shall be used as far as possible as the general base material; in the environment where the wall is too dry or the wind and light are strong, the wall shall be wetted with clear water as possible first. When there is no clear water on the wall, the putty layer shall be removed.
為了預防問題并及時解決問題，我相信我們可以避免問題藕夫。
In order to prevent problems and solve them in time, I believe we can avoid problems.
The above is the relevant content introduced by Jinan putty powder company. If you want to know more, please visit the website: http://m.bjtsdc.com
魯公網安備