1裁鸦、平直度践桂，用2米對尺子或試驗尺赔绒，墻與對尺子緊密無縫好腊拍，可有2毫米誤差字旭，“米”形對驗收較好据沈。
1. Straightness, use 2m to ruler or test ruler, the wall and ruler are the best seamless, with 2mm error, and the "meter" shape is better for acceptance.
2捶牢、陰陽角度應垂直于地面成一條直線鸠珠，用眼睛看不出任何彎曲。尤其是墻紙的墻壁秋麸，如果陰陽角度不直渐排，當墻紙?jiān)谶@些地方會出現空鼓。
2. The angle of yin and Yang shall be perpendicular to the ground in a straight line, and no bending can be seen with eyes. Especially for the wall of wallpaper, if the angle between yin and Yang is not straight, there will be hollowing when the wallpaper is in these places.
3筒臂、在工作膩?zhàn)颖砻嬗眉?xì)砂紙打磨達到反光效果烤酌，有金屬反光的感覺。不要擔心涂層或粘貼脚自。只有這樣惫康，涂層才能光滑和光澤的背后的工作。
3. Polish the surface of working putty with fine sandpaper to achieve the reflective effect, with the feeling of metal reflection. Do not worry about coating or sticking. Only in this way can the coating be smooth and glossy behind the work.
4. 在干膩?zhàn)由蠂娦┧^察膩?zhàn)邮擒浕诉€是壓碎了赢瘦。若變化不大則較好九窿，說明膩?zhàn)拥馁|(zhì)量和穩定性較好。
4. Spray some water on the dry putty and observe whether the putty is softened or crushed. If the change is small, it is better, indicating that the quality and stability of putty are better.
5. 檢查膩?zhàn)颖砻媸欠裼辛芽p汇泰。裂縫必須及時處理坦膘。檢查墻體與木制品是否有不明顯的界限。假如膩?zhàn)庸卧谀局破飞媳ⅲ瑫?huì)影響木制品的外觀光線承跟，一定要及時清理。上面面吹膩?zhàn)右部梢酝ㄟ^(guò)以上方法接受赃阀。檢查窗臺霎肯、門框等小面積處，應平整無刮縫榛斯。
5. Check the putty surface for cracks. Cracks must be treated in time. Check if there is no obvious boundary between the wall and woodwork. If the putty is scraped on the wooden products, it will affect the appearance light of the wooden products, and it must be cleaned in time. Puttying on the upper surface can also be accepted by the above methods. Check the windowsill, door frame and other small areas, which shall be flat without scratch.
魯公網安備